Moisture measurement

M-Sens WR Online Moisture Measurement for Solids

An online moisture sensor for solids with large measuring ranges and high moisture contents. It measures dust, powder, granulates, wood chips and other bulk goods, and stands up to impacts, water and abrasion.

0–85%Residual moisture range, depending on material
0.1%Absolute accuracy in the calibrated range
IP 67Sensor protection type
1,000 ftMax cable length (305 m)
M-Sens WR online moisture sensor
  • For large measuring ranges and high moisture contents
  • Measuring range of 0 to 85% residual moisture, depending on the material
  • Accuracy of 0.1% absolute in the calibrated range
  • Online moisture measurement
  • Resistant to impacts, water and abrasion, with a ceramic measuring window
  • Records both surface moisture and capillary moisture
  • Easy to install and simple to calibrate, without removing the sensor

Use

Where M-Sens WR fits

M-Sens WR measures moisture continuously in solids of all kinds, including dust, powder, granulates and wood chips. It is suited to container outlets, conveyor belts, conveyor screws, mixers and conveyor dryers.

It is a contact method, so the ceramic measuring disc has to stay covered with material at all times. Retrofitting is simple.

M-Sens WR installed on a container outlet
Container
M-Sens WR installed on a conveyor belt
Conveyor belt
M-Sens WR installed on a conveyor screw
Conveyor screw
M-Sens WR installed in a mixer
Mixer
M-Sens WR installed on a conveyor dryer
Dryer

Function

How the measurement and calibration work

M-Sens WR uses a high-frequency capacitive method that compares the dielectric constant of water with that of the material being measured. Surface and capillary moisture both strongly affect the dielectric constant, so moisture can be measured precisely as long as the average bulk density stays constant. An internal filter compensates for fluctuations caused by bulk density changes, and temperature effects are compensated automatically.

Calibration

  1. Sampling. Start a reference-point entry on the transmitter. It takes one minute. If the material is moving, take a sample downstream of the sensor.
  2. Laboratory test. Measure the residual moisture of the sample in a lab. The sample should represent what the sensor measured.
  3. Enter the value. Enter the lab value at the transmitter to complete the reference point.

One reference point gives an adequate value, and more points improve accuracy.

M-Sens WR measuring principle
Measuring principle
M-Sens WR calibration
Calibration

Mounting and installation

Mounting positions and system

  • Screw conveyor: ideal, because the product passes the probe at regular intervals and at a fairly constant bulk density.
  • Conveyor belt: a device presses the sensor onto the material so it stays in contact with the surface.
  • Hopper: install in the conical discharge section, flush with the inner wall.
  • Mixer: fits conventional mixer types and measures during mixing. The reading can feed a PLC to adjust mixing time and liquid additions.

A complete system is a welded base flange with securing ring, the sensor with plug connector, and an MME 300 transmitter. The transmitter comes as a wall-mounted unit with touch-screen control and display, or as a DIN rail version with calibration software. The probe connects to the transmitter with a shielded 4-core cable up to 1,000 ft (305 m) long.

Technical data

M-Sens WR specifications

Transcribed from the M-Sens WR product sheet, which gives several values in US units. Converted values are added in brackets. Confirm critical values against the product information PDF.

Sensor
HousingStainless steel 1.4301
Sensor surfaceMixed ceramic
Protection typeIP 67 to EN 60529
Material temperature32 to 176 °F (0 to 80 °C)Optional: up to 190 °F
Operating pressure1 bar (14.5 psi)
Power consumption0.6 W
Weight1.76 lb (0.8 kg)
Measuring range0 to 85% residual moisture, depending on the material
Measuring accuracy0.1% absolute in the calibrated measuring range
Connection cableShielded, 4-core, 0.25 mm²; max. 1,000 ft (305 m)
Transmitter
ModelMME 300
Power supply110/230 V AC (50 Hz) or 24 V DC
Power consumption20 W / 24 V
Current consumptionMax. 1 A at 24 V
Protection categoryIP 65 according to EN 60529
Operating temperature−10 to +45 °C (+14 to +113 °F)
Dimensions258 × 237 × 174 mm W × H × D (10.2 × 9.3 × 6.9 in)
WeightApprox. 2.5 kg (5.5 lb)
InterfaceRS 232, RS 485 (Modbus)
Cable glands3 × M16 (4.5–10 mm Ø)
Cable cross-section0.2–2.5 mm² (AWG 24–14)
Current output1 × 4–20 mA (0–20 mA), load < 500 Ω
Switch output, measurement alarmRelay with switchover contact, max. 250 V AC, 1 A
Digital inputs2 inputs for active external control signals
Data backupFlash

Application examples

M-Sens WR in real processes

M-Sens WR installation photo 1
M-Sens WR installation photo 2
M-Sens WR installation photo 3
M-Sens WR installation photo 4

Common questions

M-Sens WR FAQ

What is M-Sens WR used for?

Online moisture measurement in solids with large measuring ranges and high moisture contents, including dust, powder, granulates and wood chips.

What moisture range does M-Sens WR cover?

0 to 85% residual moisture, depending on the material, with an accuracy of 0.1% absolute in the calibrated range.

How does M-Sens WR work?

It uses a high-frequency capacitive method that compares the dielectric constant of water with that of the material. An internal filter compensates for bulk density changes.

How is M-Sens WR calibrated?

At the transmitter, without removing the sensor. You start a one-minute reference measurement, take a sample, measure its moisture in a lab and enter the value. More reference points improve accuracy.

Where is M-Sens WR installed?

On screw conveyors, conveyor belts, hoppers, mixers and conveyor dryers. The ceramic measuring disc has to stay covered with material.

What does a complete M-Sens WR system include?

A welded base flange with securing ring, the sensor with plug connector, and an MME 300 transmitter, connected by a shielded 4-core cable up to 1,000 ft long.

Talk with GTS

Is M-Sens WR right for your material?

Tell us what material you're measuring, where it moves and the moisture range you expect. We'll confirm whether M-Sens WR fits or recommend a better option.