Solids flow meters

DensFlow Dense-Phase Flow Meter

A measuring system for continuous flow metering of powders and granules in pneumatic dense-phase conveying and at high throughput, with an open measuring tube and no mechanics.

±2–5%Accuracy in calibrated range
25 barMax pressure, optional (363 psi)
1–10 m/sVelocity range (3.3 to 32.8 ft/s)
4–20 mAFlow output signal
DensFlow dense-phase flow measuring tube
  • Reliable flow metering in pneumatic dense-phase conveying
  • Unlimited throughput volumes can be measured
  • Optionally pressure-resistant up to 25 bar (363 psi)
  • No obstruction in the cross-section, so no dead spots where residue can form
  • Measurement is independent of the flow speed of the material
  • Simple retrofitting
  • Maintenance-free
  • Contact-free measuring method with no mechanics

Use

Where DensFlow fits

DensFlow is a measuring system developed specifically for flow metering of solids in dense-phase conveying. It is used for online measurement of:

  • Powders or granules
  • In pneumatic dense-phase transport
DensFlow installed in a dense-phase fuel conveying line
DensFlow in a dense-phase line

Function

How concentration and speed are measured

A high-frequency electromagnetic alternating field is coupled in to generate a homogeneous measuring field in the measuring pipe. Solids within this field reduce its amplitude, giving a measuring signal that corresponds to the concentration of the solids being conveyed in the measuring tube (kg/m³).

Using the same kind of sensor, the change in the alternating field is measured at two additional points in the measuring tube. These two sensors are a defined distance apart.

The analysis electronics, with an integrated correlator, determine from the two sensor signals how long the material takes to travel between the sensors. The known distance is then used to work out the speed of the solids (m/s).

From the two measured parameters, concentration (K) and speed (v), and the known cross-section (A) of the measuring tube, the flow is determined as:

Q = K × v × A

It is output as a 4–20 mA signal.

DensFlow measuring arrangement in a conveying line
DensFlow measuring arrangement

Mounting and installation

Flange installation in the conveying line

In pneumatic dense-phase conveying, the installation point is specified according to the conveying inlet and outlet paths.

The measuring tube is installed at the specified point with a flange connection. Measuring tubes are supplied as standard in nominal widths up to 150 mm (5.9 in) with flange connections in accordance with DIN 2576.

DensFlow measuring tube mounted with flanges
DensFlow flange mounting

Technical data

DensFlow specifications

Imperial values are converted from the manufacturer's metric data. Confirm critical values against the product information PDF.

Sensor
HousingStainless steel 1.4571 (316Ti), NW 10 to 125 mm (0.4 to 4.9 in), flange EN 1092-1
Inner pipeCeramic
Protection categoryIP 65 according to EN 60529/10.91
Environment temperatureSensor pipe electronics: −20 to +60 °C (−4 to +140 °F)Sensor pipe: −20 to +80 °C (−4 to +176 °F); higher temperatures as an option
Max. working pressure16 bar (232 psi), optional 25 bar (363 psi)
Working frequency100 kHz
WeightDepending on the nominal diameter
Velocity range1 to 10 m/s (3.3 to 32.8 ft/s)
Accuracy±2–5% in the calibrated range
DimensionsNW + 90 mm, L 500 mm (19.7 in)
Transmitter
Power supply110/240 V, 50 Hz; 24 V DC
Power consumption20 W / 24 VA
Protection categoryIP 65 to EN 60529/10.91
Operating temperature−10 to +45 °C (+14 to +113 °F)
Dimensions258 × 237 × 174 mm W × H × D (10.2 × 9.3 × 6.9 in)
WeightApprox. 2.5 kg (5.5 lb)
Cable glands3 × M16 (4.5–10 mm Ø)
Terminal clamp wire size0.2–2.5 mm² (AWG 24–14)
Current output signal2 × 4–20 mA (0–20 mA), load < 500 Ω
Alarm output / error outputRelay with toggle switch, max. 250 V AC, 1 A
Data backupFlash memory
Impulse outputOpen collector, max. 30 V, 20 mA
RS 485 interfaceModbus

Application examples

DensFlow in real processes

DensFlow: flow metering of coal dust in steel manufacture
Coal dustFlow metering in dense-phase conveying in steel manufacture
DensFlow: flow metering of coal dust in a steel plant
Coal dustFlow metering in dense-phase conveying in a steel plant
DensFlow: main lance monitoring during coal injection
Main lance monitoringDuring coal injection in the steel plant
DensFlow: single lance monitoring in a steel plant
Single lance monitoringIn the steel plant during firing of the furnace

Common questions

DensFlow FAQ

What is DensFlow used for?

Continuous flow metering of powders or granules in pneumatic dense-phase conveying, including at high throughput.

How does DensFlow determine the flow?

It measures the concentration of solids in the measuring tube from the damping of a high-frequency electromagnetic alternating field, and the speed of the solids by correlating the signals from two sensors a defined distance apart. Flow is Q = K × v × A, output as a 4–20 mA signal.

Does DensFlow obstruct the conveying line?

No. The installation creates no obstruction in the cross-section, so there are no dead spots where residue can form.

What pressure can DensFlow handle?

16 bar (232 psi) as standard, and optionally up to 25 bar (363 psi).

What pipe sizes is DensFlow available in?

Measuring tubes are supplied as standard in nominal widths up to 150 mm (5.9 in) with flange connections in accordance with DIN 2576.

How accurate is DensFlow?

±2–5% in the calibrated range.

Talk with GTS

Is DensFlow right for your material?

Tell us what you're conveying, the line size and the conveying pressure. We'll confirm whether DensFlow fits or recommend a better measurement principle.